EZ-Clone Neoprene Replacement Inserts – Soft 35 Pack

EZ-Clone Neoprene Replacement Inserts – Soft 35 Pack are sterile cloning collars designed for use in most aeroponic cloning systems. Each insert is pre-slit for fast, easy cutting insertion and manufactured from a soft neoprene material that holds cuttings firmly without compressing or tearing delicate stem tissue. This 35-pack keeps your cloner running through a full propagation cycle without running short on collars.

EZ-Clone Neoprene Replacement Inserts – Soft 35 Pack Specifications

The specifications below are drawn from manufacturer data and the canonical product listing. The soft collar is the original EZ-Clone collar formulation; a hard-collar variant is also available separately.

Why Choose EZ-Clone Neoprene Replacement Inserts – Soft 35 Pack

Neoprene collar quality has a direct impact on rooting outcomes. A collar that grips too tightly can bruise the cambium layer on soft-stemmed cuttings; one that is too loose allows air gaps around the stem, which dries out the cut end and interrupts the misting cycle. EZ-Clone engineered these soft inserts specifically to hit the middle ground: firm enough to hold a cutting upright in the spray zone, flexible enough to avoid tissue damage on delicate species.

• Sterile material: Each collar is manufactured from a sterile neoprene compound, reducing the risk of introducing pathogens into the cloning chamber during propagation.
• Pre-slit design: The factory-cut slit lets you seat a cutting in seconds. There is no need to cut the collar yourself, which removes a potential contamination point and speeds up the loading process when handling large numbers of cuttings at once.
• Tissue-safe softness: The soft formulation flexes around the stem rather than compressing it, which is particularly important for herbaceous cuttings and young clones with thin stems.
• Designed for EZ-Clone systems: Collar geometry matches the standard collar seat dimensions used in EZ-Clone aeroponic cloners, so they drop in without modification or trimming.
• 35-pack quantity: The pack size aligns with popular EZ-Clone unit capacities, giving growers a full replacement set in one purchase.

Best Uses for EZ-Clone Neoprene Replacement Inserts – Soft 35 Pack

These collars are a consumable part of any aeroponic propagation workflow. They are most useful in the following scenarios:

• Routine collar replacement: Neoprene collars compress and accumulate mineral deposits over repeated use cycles. Swapping in fresh collars at the start of each propagation run maintains consistent stem support and reduces the risk of cross-contamination between batches.
• High-turnover propagation rooms: Growers running back-to-back cloning cycles benefit from keeping a stock of replacement inserts on hand so a spent set can be swapped out without waiting for a re-order.
• Soft-stemmed and herbaceous cuttings: The soft neoprene variant is the right choice for basil, tomato, pepper, and other herbaceous species where a firmer collar could bruise the cutting at the collar interface.
• EZ-Clone 16, 30, 64, and similar aeroponic cloners: The collar geometry is matched to EZ-Clone’s standard site cup openings, making these a direct fit for most units in the EZ-Clone product line.
• Mixed-media propagation setups: In setups where cuttings are transferred to fabric containers or other growing media after rooting, fresh collars keep each new cloning batch starting clean.

Compatibility

EZ-Clone neoprene inserts are designed for use in most aeroponic cloning systems that use a standard neoprene collar seat. They are the factory-specified replacement collar for EZ-Clone branded aeroponic cloners and are compatible with other aeroponic cloners that use collars of the same diameter profile.

The soft variant is best suited to cuttings with stems up to approximately pencil-width diameter. For woody or thick-stemmed cuttings that require more lateral support in the collar seat, the EZ-Clone hard collar variant may provide a better fit. Both variants use the same outer geometry and seat in the same clone site cups.

These inserts are intended for single-use or limited-reuse in a single propagation cycle. They are not designed for long-term reuse across many cycles, as neoprene foam compresses over time and the slit widens with repeated insertions and removals. Starting each cycle with fresh collars from a clean, sealed storage container is good practice for maintaining sterile conditions.

Usage Guidelines

Neoprene inserts are straightforward to use, but a few practices help maximize rooting success:

• Start with clean hands or gloves: Because the material is sterile out of the pack, handle inserts with clean nitrile gloves to avoid introducing surface bacteria before the collar enters the cloning environment.
• Use the pre-slit as-is: Insert the cutting stem through the slit without widening it manually. The factory slit is sized to grip the stem with light pressure; forcing a wider opening reduces that grip and can leave an air gap around the stem.
• Seat the collar flush: Push the collar down into the clone site cup until it sits flush with the lid surface. A collar seated too high can allow light into the root zone and interfere with the misting spray pattern.
• Inspect after each cycle: After removing rooted clones, inspect each collar for compression, discoloration, or algae growth. Compressed or discolored collars should be discarded and replaced rather than reused in the next cycle.
• Store unused inserts sealed: Keep the remaining collars in the original packaging or a sealed bag in a cool, dry location to preserve the sterile condition between cycles.

Sources & Further Reading