Hose Connector

The Auto Pot Hose Connector (SKU APWS084) is a compact irrigation fitting designed to join or extend 1/2-inch tubing runs in AutoPot gravity-fed watering systems. Measuring 3 × 1 × 1 in and weighing 0.4 lbs, it is small enough to fit neatly between pots or along a tray edge while maintaining a secure, leak-resistant connection. If you are expanding an existing AutoPot layout or replacing a worn fitting, this connector is the direct replacement part.

Hose Connector Specifications

All measurements are taken from the canonical product record (SKU APWS084). The material note is inferred from standard AutoPot fitting practice and is marked accordingly.

Why Choose the Auto Pot Hose Connector

AutoPot systems are built around a specific tubing ecosystem. Using a matching branded connector means the fitting is dimensioned to the same tolerances as the tubing it joins. That matters in gravity-fed systems where water pressure is low and even a small gap at the joint can cause drips, dry spots in the root zone, or flooding of the tray.

Below are the practical reasons growers reach for this fitting rather than a generic hardware-store alternative:

• Correct tubing diameter. The connector is sized for 1/2-inch AutoPot supply hose, so it seats fully without adapters or hose clamps.
• Compact footprint. At 3 × 1 × 1 in the fitting tucks neatly alongside pots or under trays, leaving the grow area uncluttered.
• Low shipping weight. The 0.4-lb unit weight means adding several spares to an order adds negligible cost, which is useful when building out a large system in stages.
• Direct replacement part. Growers who already run AutoPot systems can identify this fitting by its SKU (APWS084) and order a like-for-like replacement without measuring or guessing.
• Low unit cost. At under $9 retail, keeping a spare on hand costs less than a service call or lost crop day from a split fitting.

Best Uses for the Auto Pot Hose Connector

This fitting serves a narrow, specific role: joining two sections of 1/2-inch irrigation tubing in a passive or gravity-fed hydroponic layout. The scenarios below reflect the category this product belongs to — drip and irrigation kits in hydroponic systems and water management.

• Extending an AutoPot supply run. When a reservoir is positioned farther from the pots than the included hose length allows, a connector joins two hose segments cleanly.
• Repairing a split or kinked section. Rather than replacing an entire hose run, growers cut out the damaged section and splice the remaining hose with this connector.
• Building a custom AutoPot layout. Larger greenhouse or tent setups often route tubing around obstacles such as columns or drainage channels; connectors allow bends to be made with straight-hose segments rather than forcing a curve.
• Spare-parts inventory for commercial grows. Operations running dozens of AutoPot trays keep a handful of connectors on the shelf to avoid downtime when a fitting fails mid-cycle.
• Integration with inline filtration. If you are adding an inline screen filter to your supply line — such as the Dilution Solutions 1-1/2 in filter with 200-mesh screen upstream of a nutrient dosing point — hose connectors allow you to segment the run and insert the filter without cutting into the main trunk line.

Compatibility

The Auto Pot Hose Connector is designed for use with the AutoPot watering system range. It accepts standard 1/2-inch outside-diameter supply tubing of the type included with AutoPot tray kits. It is a passive fitting — there are no electrical components, pumps, or sensors — so it has no voltage or temperature operating specification beyond the normal range for indoor cultivation environments (typically 50–95 °F / 10–35 °C ambient).

This connector is not intended for high-pressure irrigation lines. AutoPot systems operate by gravity feed from a sealed reservoir, and the fitting is rated for that low-pressure use case. Do not use it in systems where supply pressure exceeds gravity-head levels without confirming compatibility with AutoPot directly.

If your system also requires water quality management, consider pairing your AutoPot setup with a reverse-osmosis unit such as the Hydro-Logic Micro 75 GPD compact RO system to reduce mineral scaling on fittings over time. For nutrient solution aeration in connected reservoirs, the Active Aqua air pump (1–8 outlets) is a common companion in multi-tray setups.

Sources & Further Reading